19 December 2009

Yusynth (Part 15)

I finished another module today. I had this PCB lying around for a long time. It is a Yusynth VCA module. There is one tricky thing you need to do while building this module and that is to match two BC547C transistors. It is only possible to do this when you have a multimeter that is capable of measuring the HFE (amplification) factor of a transistor. The reason this is necessary is that they will work in pairs.

Building this module even though it is not that complicated was special for me, because it is the first module that both has a PCB that I made myself and a front panel that I designed myself. Again I used a 2 potmeter bracket from Bridechamber. After this it was time to start wiring again. I started as usual with the wiring to connect the front panel components. After that the wires on the PCB. Because there is no silk screen on the PCB, I made sure to use different colored wires to be able to tell what is what later on.

Then it was time to test and calibrate. Yves has a nice calibration procedure on this website, but I misread it. I spend over an hour trying to calibrate it, but it didn't work like I expected. The first thing to do is put the front panel potmeters for the audio and CV input to maximum, but I also put the Gain potmeter to maximum while it should have been on the minimum position. After I found that out calibration was a piece of cake actually :) It is a nice VCA, quite quick actually. I even used the LFO to do audio rate stuff with it.

Here is the finished module in my modular desk. As you can see I still haven't fastened any of them. I have been looking for nice black screws for a long time. I think I found them now. Actually guitar screws for mounting pickups to a guitar body. They have a big head and are not too long. I found them on E-bay somewhere in the UK from a guitar shop. Another thing I'm still thinking about is how I should layout all the modules so that it is kind of logical. Because I'm screwing them directly into the wood of the cabinet I don't want to move them too much since I'm sure that the wood will get damaged and after a couple of times it won't hold anymore. Well next up are the two Yusynth LFO modules you also see in the picture. I'll update you soon.

10 comments:

Unknown said...

Hey,

Ik ben op dit moment ook met de VCA van Yusynth bezig, de VCO heb ik bijna af, het is nog wachtten op de tempco weerstand. Maar ik had een vraag betreffende die torren, hoe match je die eigenlijk? Zelf heb ik niet genoeg ervaring denk ik om dat te doen, is het moeilijk? is het te leren? Graag hoor ik hier iets meer over aangezien ik binnenkort(aankomende week) wil beginnen met het solderen van de componenten.

Alvast bedankt,
Groeten Aernout Ottens
http://aernout.colourmotion.nl

Synth.nl said...

Als je een multimeter hebt die HFE kan meten is dat de makkelijkste methode. Je stopt de transistors in de speciaal daarvoor bedoelde sockets en noteert de HFE waarde (versterkingsfactor). Dan zoek je van een hele stapel diegenen uit die slechts 1 of 2 punten uit elkaar liggen. Hier staat een andere methode beschreven: http://electro-music.com/forum/topic-18365-0.html&postdays=0&postorder=asc&highlight=

Unknown said...

Hartelijk dank voor het antwoord, werkte perfekt :) ik had nog een multimeter liggen die dit klusje kon klaren.

Nog 1 vraag echter, ik heb nu de dc versie van de vca gebouwt. Ik zag bij u op de foto de ac versie. Wat is het verschil? Hoe zit het met de voeding? Is het beter?

Synth.nl said...

De AC versie is bedoeld voor audio signalen terwijl de DC bedoeld is voor CV signalen. Meestal gebruik je een VCA op audio signalen om volume te moduleren. Dus de AC versie lijkt mij logischer. Wat bedoel je precies met voeding?

Unknown said...

Aah kijk, ik meende AC/DC als in stroom. Achteraf is dit dus verschrikkelijk stom gedacht, maar ja, electronica is niet altijd mijn sterkste punt geweest.(begint het nu wel te worden) Dan denk ik dat ik mijn DC versie om ga bouwen naar AC. Moet wel lukken denk ik, heb nu wel alleen de verkeerde pots besteld :(

Synth.nl said...

Hoi, dat van die potmeters geeft niet hoor. Ik heb hem ook met lineaire potmeters gebouwd. Werkt prima.

Unknown said...

Hey hallo,

De VCA is nu af, en deze werkt ook, ik heb alleen moeite met het kalibreren. Ik begin met P2 en P3 open (input en cv) en met P1 dicht. Dan stel ik de sinus mooi bij zodat deze symmetrisch is. Dit klopt. Maar dan moet ik P3 dichtdraaien, en dat moet het signaal muten. Dit doet het bij mij echter niet. Hoeveel ik ook aan A2 draai, ik krijg het signaal niet weg. Ik heb al gekeken of deze trimmer misschien een te hoge waarde was, maar hij was precies 1k. Doe ik iets verkeerd?

Synth.nl said...

Je krijgt hem niet HELEMAAL weg. Maar wel zo goed als. Ik zou me er niet te druk over maken. Als de VCA verder gewoon werkt is het prima hoor :)

Unknown said...

Het is bij mij meer dat het signaal helemaal niet verandert als ik aan de cv potmeter draai. Kan u misschien het kalibratie proces in het Nederlands uileggen? Misschien interpreteer ik het verkeerd.

Synth.nl said...

Hoi nou helemaal vertalen is wel wat veel werk :) Maar bij het afstellen van deze trimmer moet je CV en Gain iig helemaal naar links draaien, dicht dus. Ik denk dat dat het probleem is.